在分角上， 我的问题是，在启动docker服务之前，我没有安装并启动iptables。在启动docker服务之前，请确保iptables服务已启动并运行。

对于Ubuntu 19.04使用openconnect 8.3进行VPN，我必须将/etc/resolve.conf符号链接到systemd中的文件(与answerby wisbucky相反)

执行ln -sf /etc/resolv.conf /run/systemd/resolve/resolv.conf

调试步骤

连接到公司VPN 在/etc/resolv.conf或/run/systemd/resolve/resolv.conf中查找正确的VPN设置 无论哪个有正确的DNS设置，我们都会将其符号链接到另一个文件 (提示:在赋值的左边放置一个设置正确的)

Docker版本:Docker版本19.03.0-rc2，构建f97efcc

只是在这里添加这个，以防有人在运行docker的virtualbox容器中遇到这个问题。我将virtualbox网络重新配置为桥接而不是nat，问题就消失了。

我不知道我在做什么，但这对我很有用:

OTHER_BRIDGE=br-xxxxx # this is the other random docker bridge (`ip addr` to find)    
service docker stop

ip link set dev $OTHER_BRIDGE down
ip link set dev docker0 down
ip link delete $OTHER_BRIDGE type bridge
ip link delete docker0 type bridge
service docker start && service docker stop

iptables -t nat -A POSTROUTING ! -o docker0 -s 172.17.0.0/16 -j MASQUERADE
iptables -t nat -A POSTROUTING ! -o docker0 -s 172.18.0.0/16 -j MASQUERADE

service docker start

它帮助我:

sudo ip link delete docker0
sudo systemctl stop docker.socket
sudo systemctl stop docker.service

sudo systemctl start docker.socket
sudo systemctl start docker.service

注意:在此之后，接口docker0的ip地址必须是smth，如下所示:

inet 172.17.0.1/16 brd 172.17.255.255 scope global docker0

我使用的是Arch Linux，在尝试了以上所有的答案后，我意识到我的机器上启用了防火墙，nftables，并禁用它。我说:

sudo systemctl disable nftables
sudo systemctl stop nftables
sudo reboot

我的网卡:

➜  ~ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN mode DEFAULT group default qlen 1000
    link/ether 68:f7:28:84:e7:fe brd ff:ff:ff:ff:ff:ff
3: wlp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DORMANT group default qlen 1000
    link/ether d0:7e:35:d2:42:6d brd ff:ff:ff:ff:ff:ff
4: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default 
    link/ether 02:42:43:3f:ff:94 brd ff:ff:ff:ff:ff:ff
5: br-c51881f83e32: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default 
    link/ether 02:42:ae:34:49:c3 brd ff:ff:ff:ff:ff:ff
6: br-c5b2a1d25a86: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default 
    link/ether 02:42:72:d3:6f:4d brd ff:ff:ff:ff:ff:ff
8: veth56f42a2@if7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master docker0 state UP mode DEFAULT group default 
    link/ether 8e:70:36:10:4e:83 brd ff:ff:ff:ff:ff:ff link-netnsid 0

和我的防火墙配置，/etc/nftables.conf，我现在禁用了，将来会尝试改进，这样我就可以正确设置docker0网卡规则:

#!/usr/bin/nft -f
# vim:set ts=2 sw=2 et:

# IPv4/IPv6 Simple & Safe firewall ruleset.
# More examples in /usr/share/nftables/ and /usr/share/doc/nftables/examples/.

table inet filter
delete table inet filter
table inet filter {
  chain input {
    type filter hook input priority filter
    policy drop

    ct state invalid drop comment "early drop of invalid connections"
    ct state {established, related} accept comment "allow tracked connections"
    iifname lo accept comment "allow from loopback"
    ip protocol icmp accept comment "allow icmp"
    meta l4proto ipv6-icmp accept comment "allow icmp v6"
    #tcp dport ssh accept comment "allow sshd"
    pkttype host limit rate 5/second counter reject with icmpx type admin-prohibited
    counter
  }
  chain forward {
    type filter hook forward priority filter
    policy drop
  }