我昨天把我的Windows 10升级到最后一次更新,现在,当我启动vagrant up命令时,我得到了这个错误:

==> default: Booting VM...
==> default: Waiting for machine to boot. This may take a few minutes...
The guest machine entered an invalid state while waiting for it
to boot. Valid states are 'starting, running'. The machine is in the
'poweroff' state. Please verify everything is configured
properly and try again.

If the provider you're using has a GUI that comes with it,
it is often helpful to open that and watch the machine, since the
GUI often has more helpful error messages than Vagrant can retrieve.
For example, if you're using VirtualBox, run `vagrant up` while the
VirtualBox GUI is open.

The primary issue for this error is that the provider you're using
is not properly configured. This is very rarely a Vagrant issue.

当我尝试与GUI我有这个错误:

Failed to open/create the internal network 'HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter' (VERR_INTNET_FLT_IF_NOT_FOUND).
Failed to attach the network LUN (VERR_INTNET_FLT_IF_NOT_FOUND).

我重新安装了VirtualBox 5.0.10和扩展包, 重新配置主机以太网适配器,但总是相同的错误…

什么好主意吗?


当前回答

我从Windows 7升级到Windows 10后也遇到了同样的问题。试了所有流行的答案,但都没用。最后,我知道Windows更改了适配器的名称。虚拟盒配置为使用Realtek PCIe GBE系列控制器,而设备管理器将此作为Realtek PCIe GBE系列控制器#2。选择合适的控制器解决了这个问题。

其他回答

打开网络和共享中心,转到侧栏中的更改适配器设置。 在适配器列表中右键单击主机专用适配器,然后配置按钮->驱动程序选项卡->更新驱动程序按钮。 选择浏览我的电脑…在下一个对话框中选择Let me pick ....您应该看到其中只有主机驱动程序的列表。 选择它并单击下一步。驱动更新后,请重新尝试在虚拟机中使用主机网络。

我已经工作了一段时间,所有你需要做的是打开VirtualBox,

文件>首选项/网络>主机专用网络

您将看到VirtualBox主机专用以太网适配器

点击它,然后编辑。

我对流浪虚拟机的IP设置为192.168.10.10,您应该修改到您的虚拟机IP

这是我的网络设置;

我找到了解决问题的办法, 在我的网络适配器中有一个冲突,我只是禁用了错误消息中出现的那个,然后再次启动运行命令,在从窗口获得许多批准消息后,已经创建了一个新的适配器。

我希望这个解决方案能在某些情况下有所帮助。

对我来说,将VirtualBox更新到5.1.23解决了这个问题。Windows版本可从官方网站下载。

Open Control Panel >> Network and Sharing Center. Now click on Change Adapter Settings. Right click on the adapter whose Name or the Device Name matches with VirtualBox Host-Only Ethernet Adapter # 3 and click on Properties. Click on the Configure button. Now click on the Driver tab. Click on Update Driver. Select Browse my computer for drivers. Now choose Let me pick from a list of available drivers on my computer. Select the choice you get and click on Next. Click Close to finish the update. Now go back to your Terminal/Powershell/Command window and repeat the vagrant up command. It should work fine this time.

https://www.howtoforge.com/setup-a-local-wordpress-development-environment-with-vagrant/